XPERIA Z Multi Surface Mount (SKU 16553)SKU: 16553
ZS Multi Surface Suction Car Mount for the XPERIA Z.
Bespoke dedicated clip in cradle.
Use directly on the dashboard or apply to the glass of your windshield.
Holder is molded to contour the Sony Xperia Z L36H / C6603 smartphone.
Not suitable for use with a case or skin.
The ZS mount works on most flat surfaces.
Apply directly to dashboards, console areas or windscreens
NO NEED FOR ADDITIONAL DASH DISCS or FRICTION MOUNTS.
Part of our NEW range of Mobile Phone / Smart Phone mounts with dedicated cradles which will hold to almost any flat surface within your vehicle.
Simply apply directly to a convenient flat area and view your XPERIA Z within your line of sight or apply to the windscreen in the traditional way for a really FIRM grip to glass.
The ZS Multi Surface Mount uses a special PU coated 60mm suction cup which, although tacky to touch, it is NOT adhesive so it can be remove and re- apply as many times as you like allowing you to adjust it's position or transfer it between vehicles.
The PU coated lever release suction cup gives reliable vacuum grip that holds firm to just about any surface within your car.
The sucker requires a minimum flat area of just 70mm diameter for a good grip.
This mount will even hold to textured dashboards and console areas.
So versatile, neat enough for small cars and perfect for larger vehicles such as Motorhomes, MPVs, Lorry Cabs, Transit Vans.
If your vehicle has a deep dash or steep sloping windscreen, the ZS Multisurface Mount allows you to bring your mobile phone / smart phone closer to you for easier viewing.
The dedicated XPERIA Z cradle is bespoke and is designed to allow full access to all ports and buttons. (again remember that this cradle will not accommodate a case or skin)
Arm length approx 60mm - low level design, neat and unobtrusive.
How to apply your ZS Multi Surface Mount.
Select your chosen position, ensure it is clean, dust free.
Remove the protective film from the sucker.
Position the ZS arm pull down the lever to expel the air and create the vacuum.
Give it a wiggle to ensure it's holding firm then insert your phone onto the dedicated Galaxy Note holder.
Just lift the lever and pull on the release tab to break the vacuum.
The ZS mount can now be removed
NOTE: Please do not just pull the mount off the surface, you WILL damage it.
Washable; Although your car is probably spotless, dust, fluff & grease can build up on the suction cup causing the suction to fail. If this happens simply rinse the sucker under a running tap & leave to air dry.
Not suitable for oiled areas, loose covered dashboards or areas cleaned with wax or grease treatments.
This item is a bespoke cradle and is suitable only for the XPERIA Z
This bespoke cradle is not suitable for use with a case or skin.
View the Video below to see how the ZS Multi-surface Mount works.
Note - may not show the holder for your device.
|Bullet 1||ZS Multi-Surface Suction Car Mount with dedicated clip-in cradle made & designed to hold the Sony XPERIA Z L36H / C6603 securely on the mount; use directly on the dashboard or apply to the glass of your windshield.|
|Bullet 2||The ZS mount works on most flat surfaces, NO NEED FOR ADDITIONAL DASH DISCS or FRICTION MOUNTS, simply apply directly to a convenient flat area and view your Sony XPERIA Z within your line of sight or apply to the windscreen in the traditional way for a r|
|Bullet 3||The ZS Multi-Surface Mount uses a special PU coated 60mm (2.3") suction cup which, although tacky, is NOT adhesive so it can be removed and re-applied many times allowing for position readjustment or transfer between vehicles.|
|Bullet 4||If your vehicle has a deep dash or a steep sloping windscreen, the ZS Multi-surface Mount allows you to bring your cell phone / smart phone closer for easier viewing.|
|Bullet 5||The dedicated Sony XPERIA Z cradle is bespoke and designed to allow full access to all ports and buttons (this cradle will not accommodate the device using a case or skin).|